PCIe/104 Spartan-6 XC6SLX45T User Programmable FPGA Module

FPGA35S6046HR & FPGA35S6101HR
PCIe/104 Xilinx Spartan-6 User Programmable FPGA Modules

Operating Temperature -40° to +85°C

 

Key Features

• PC/104 form factor
• PCIe/104 stackable bus structure
  • PCIe universal expansion bus (Type 1 or Type 2)
• PCIe x1 interface
• Xilinx Spartan-6 FPGA (device options listed below)
  • XC6SLX45T
    • 46,661 Logic Cells
    • 2,489 Kb of internal RAM
    • Provides PCIe interface (PCIe is not repopulated)
  • XC6SLX100T
    • 101,261 Logic Cells
    • 5,800 Kb of internal RAM
    • Provides PCIe interface (PCIe is not repopulated)
• 1.0 Gbit of DDR2 SDRAM (configured as 64M x 16)
• Onboard flash for FPGA configuration
  • No need to re-load FPGA at power up
• Onboard 27 MHz oscillator
• Provides a hardware platform for user to create FPGA code and drivers

 

Description

The FPGA35S6046 and FPGA35S6101 are PC/104 FPGA modules with a PCIe/104 stackable bus structure. The FPGA35S6xxx modules provide a platform for customer developed FPGA code. They are based on a Xilinx Spartan-6 with a hardware PCIe x1 endpoint to provide the interface to the host CPU. On board DDR2 memory provides dedicated storage space for the FPGA application. They feature four RS-232/422/485 transceivers connected to FPGA pins allowing custom serial port implementations. A total of 96 I/O pins interface the FPGA to the outside world, and allow for a variety of signal levels.

 

I/O

• 32 RS-232/422/485 I/O
  • Four connectors
  • Each connector can support a single full RS-232 port or two TX/RX only ports
  • Up to 1 Mbps in RS-232 mode
  • Up to 20 Mbps in RS-422/485 mode
  • ESD Protected
• 24 5V tolerant Digital I/O
  • Selectable pull-up/pull-down per byte
  • Pull-up can be 3.3V or 5V
  • ESD Protected
  • Can be used as LVDS Input/Output or LVTTL Input/Output
• 40 3.3V tolerant High-Speed I/O
  • Can be used as LVDS Input or LVTTL Input/Output
• Xilinx JTAG Connector for FPGA programming
   
• Software

• Sample FPGA to demonstrate I/O pins, DDR memory, and PCIe interface
• DOS example program to use with sample FPGA
• Custom driver development required for other operating systems (e.g. Windows and Linux)
• Use of a driver development toolkit such as Jungo WinDriver is recommended

 

Recommended Accessories

• SK-FPGA35S6046HR Starter Kit
  • FPGA35S6046 Module
  • Xilinx Platform Cable USB II
• SK-FPGA35S6101HR Starter Kit
  • FPGA35S6101 Module
  • Xilinx Platform Cable USB II
• XK-CM30 - set of four 10-pin DIL to 9-pin D-sub cables
• TB50 - 50 position screw terminal board
• XB50 - 50 position screw terminal extender board
• XT50 - 50-pin twisted pair cable XP50 - 50-pin flat ribbon cable

 

Physical Attributes

• Dimensions
  • Length: 3.775 inches (95.89 mm)
  • Width: 3.550 inches (90.17 mm)
  • Stand-off Height: 0.600 inches (15.24 mm)
• Weight: Approximately 0.14 lbs. (0.06 Kg)
• Standard Operating Temperature, 90% humidity non-condensing: -40 to +85°C
• Storage Temperature: -55 to +125°C
• Power Consumption: 2.5 W @ 5 V typical

 

 

Ordering Information

Part Number	Description
FPGA35S6046HR	PCIe/104 Spartan-6 XC6SLX45T User Programmable FPGA Module
SK-FPGA35S6046HR	Kit: FPGA35S6045HR with Xilinx Platfrom Cable USB II
FPGA35S6101HR	PCIe/104 Spartan-6 XC6SLX100T User Programmable FPGA Module
SK-FPGA35S6101HR	Kit: FPGA35S6100HR with Xilinx Platform Cable USB II